Adjunctive hyperbaric oxygen therapy for irradiated rat calvarial defects

PURPOSE: The aim of this study was to conduct a histologic evaluation of irradiated calvarial defects in rats 4 weeks after applying fibroblast growth factor-2 (FGF-2) with hyaluronan or biphasic calcium phosphate (BCP) block in the presence or absence of adjunctive hyperbaric oxygen (HBO) therapy. METHODS: Twenty rats were divided into HBO and non-HBO (NHBO) groups, each of which was divided into FGF-2 and BCP-block subgroups according to the grafted material. Localized radiation with a single 12-Gy dose was applied to the calvaria of rats to simulate radiotherapy. Four weeks after applying this radiation, 2 symmetrical circular defects with a diameter of 6 mm were created in the parietal bones of each animal. The right-side defect was filled with the materials mentioned above and the left-side defect was not filled (as a control). All defects were covered with a resorbable barrier membrane. During 4 weeks of healing, 1 hour of HBO therapy was applied to the rats in the HBO groups 5 times a week. The rats were then killed, and the calvarial specimens were harvested for radiographic and histologic analyses. RESULTS: New bone formation was greatest in the FGF-2 subgroup, and improvement was not found in the BCP subgroup. HBO seemed to have a minimal effect on new bone formation. There was tendency for more angiogenesis in the HBO groups than the NHBO groups, but the group with HBO and FGF-2 did not show significantly better outcomes than the HBO-only group or the NHBO group with FGF-2. CONCLUSIONS: HBO exerted beneficial effects on angiogenesis in calvarial defects of irradiated rats over a 4-week healing period, but it appeared to have minimal effects on bone regeneration. FGF-2 seemed to enhance new bone formation and angiogenesis, but its efficacy appeared to be reduced when HBO was applied.

Fabrication of immediate complete denture using Campagna tray technique / 대한치과보철학회지

An immediate complete denture is considered as restoration for lost natural teeth, which is fabricated following the extraction of the remaining teeth. Current esthetics and function can be retained by using immediate denture without edentulous period. However, the major disadvantages of immediate denture relate to the difficulties associated with taking accurate definitive impression and predicting the results of immediate denture. In this case report, the Campagna tray technique was used to take the final impression in a 49-year-old male patient presented with all remaining teeth diagnosed as hopeless teeth. Surgical templates were used for alveoloplasty after extraction. The immediate complete dentures were then delivered. The clinical assessments of immediate dentures showed good esthetic and functional outcomes. The patient showed high level of satisfaction.

Postoperative irradiation after implant placement: A pilot study for prosthetic reconstruction

PURPOSE: On maxillofacial tumor patients, oral implant placement prior to postoperative radiotherapy can shorten the period of prosthetic reconstruction. There is still lack of research on effects of post-implant radiotherapy such as healing process or loading time, which is important for prosthodontic treatment planning. Therefore, this study evaluated the effects of post-implant local irradiation on the osseointegration of implants during different healing stages. MATERIALS AND METHODS: Custom-made implants were placed bilaterally on maxillary posterior edentulous area 4 weeks after extraction of the maxillary first molars in Forty-eight Sprague-Dawley rats. Experimental group (exp.) received radiation after implant surgery and the other group (control) didn't. Each group was divided into three sub-groups according to the healing time (2, 4, and 8 week) from implant placement. The exp. group 1, 2 received 15-Gy radiation 1 day after implant placement (immediate irradiation). The exp. group 3 received 15-Gy radiation 4 weeks after implant placement (delayed irradiation). RESULTS: The bone mineral density (BMD) was significantly lower in the immediate irradiation groups. BMD was similar in the delayed irradiation group and the control group. The irradiated groups exhibited a lower bone-to-implant contact ratio, although the difference was not statistically significant. The irradiated groups also exhibited a significantly lower bone volume and higher empty lacuna count than the control groups. No implant failure due to local irradiation was found in this study. CONCLUSION: Within the limits of this study, the timing of local irradiation critically influences the bone healing mechanism, which is related to loading time of prostheses.

Reinforcing the retention of provisional restoration using provisional implant on maxillary anterior region: clinical case report / 대한치과보철학회지

Proper management of provisional prosthesis is key to success in prosthodontics. Provisional restoration on maxillary anterior missing area frequently come across a incident of falling off especially in patients with long span pontics and oval arch shape. This is because maxillary anterior teeth are more exposed to horizontal force than the posterior teeth and additional anterior cantilever effect will negatively affect to the retention of provisional prosthesis. Beside that maxillary anterior provisional prosthesis should provide proper incisal guidance during the mandibular functional movements. However occlusal contacts on the prosthesis in maximum intercuspal position are located on opposite side of fulcrum line of prosthesis which will cause removing force against the provisional prosthesis. This case report present that provisional implant prevent pre-described harmful effect on maxillary anterior fixed provisional prosthesis and provide comfort and satisfactory result during post-extraction healing period.

Morphometric analysis of maxillary alveolar regions for immediate implantation

PURPOSE: The purpose of this study was to provide an actual guideline in determining the shape, diameter, and position of the implant in immediate implantation by the measurement of the thickness of facial and palatal plate, the thickness of cortical bone on the facial and palatal plate, the diameter of the root, and the distance between the roots in the cadavers. MATERIALS AND METHODS: The horizontal sections of 20 maxillae were measured and analyzed to obtain the average values. Resin blocks were produced and cut serially at 1 mm intervals from the cervical line to the root apex. Images of each section were obtained and the following measurements were performed: The thickness of the facial and palatal residual bone at each root surface, the thickness of the facial and palatal cortical bone at the interdental region, the diameter of all roots of each section on the faciopalatal and mesiodistal diameter, and the interroot distance. Three specimens with measurements close to the average values were chosen and 3-dimensional images were reconstructed. RESULTS: The thickness of the facial and palatal cortical bone at the interdental region in the maxilla, the buccal cortical bone was thicker in the posterior region compared to the anterior region. The interroot distance of the alveolar bone thickness between the roots increased from anterior to posterior region and from coronal to apical in the maxilla. CONCLUSION: In this study, the limited results of the morphometric analysis of the alveolar ridge using the sections of maxilla in the cadavers may offer the useful information when planning and selecting optimal implant for immediate implantation in the maxilla.

The current status and future tasks of the prosthodontics curriculum in Korean dental schools and graduate dental schools / 대한치과보철학회지

PURPOSE: Prosthodontics education of Korean dental schools is developing under liberal regulation according to the character of each school. Diversity in the current environment and condition for each school make it impossible to apply the same and uniform education curriculum. Therefore the purpose of this paper is to analyze and validate the status of the 2012 prosthodontics education curriculum in Korean dental schools, and to suggest future direction. MATERIALS AND METHODS: A survey was completed by all the 11 dental schools in South Korea. RESULTS: The number of students, age, sex, credits for prosthodontics lecture and practice courses, evaluation method before senior students' clinical practice, modalities for minimum requirement for graduation, beginning and finishing timing of clinical practice and faculty personnel involved in the education varied among the dental schools. CONCLUSION: High-quality educators leading an expanded teaching personnel are required, education hours must be increased and efficient curriculum must be organized to improve the prosthodontics education.

Full mouth rehabilitation of the patient with worn dentition using full-contour monolithic zirconia prostheses at an increased vertical dimension of occlusion: a case report / 대한치과보철학회지

Excessive occlusal wear results in unacceptable damage to the occluding surfaces, and can cause pulpal injury, occlusal disharmony, impaired function, and aesthetic deformity. Patients with severely worn dentition need to be classified as several categories relative to the vertical dimension of occlusion (VDO) and the interocclusal distance for the prosthetic space. When treating patients classified as those who have excessive wear without loss of occlusal vertical dimension but with limited space, we could consider treating them at an increased vertical dimension of occlusion. Treatments at an increased vertical dimension of occlusion may provide stability, given that the amount of its increase was minimal, and a perfected occlusion was achieved after enough stabilization period. A 50-year-old male visited the department of Prosthodontics in Yonsei University Dental Hospital with the chief complaint of worn teeth on lower anterior area. Reconstruction at an increased vertical dimension of occlusion was planned. After the compatibility of the new vertical dimension of occlusion had been confirmed under interim fixed restorations, definitive fixed restorations composed of full-contour monolithic zirconia prostheses were placed. This case presents that a satisfactory clinical result was achieved by restoring the worn dentition at an increased vertical dimension of occlusion with an improvement in esthetics and function.

Esthetic restoration of subgingival crown-root fractured maxillary anterior tooth using surgical extrusion / 대한치과보철학회지

Surgical extrusion, immediate extrusion following tooth luxation, is a method to preserve one's natural tooth and achieve esthetic restoration without additional periodontal surgery when subgingival dental caries or crown fracture occurs. A 16-year-old male was referred to the clinic from the department of operative dentistry for the esthetic restoration of maxillary left lateral incisor. Due to the crown to root fracture, the tooth was endodontically treated with a buccal crown length of 4 mm. When the palatal flap was elevated, the mesiopalatal cervical fracture area was situated 3 - 4 mm subgingivally. Crown lengthening was achieved through surgical extrusion. After 3 months of clinical observation and provisional restoration, the maxillary left central incisor was restored with all ceramic crown and obtained a satisfactory clinical result.

Drying time of tray adhesive for adequate tensile bond strength between polyvinylsiloxane impression and tray resin material

STATEMENT OF PROBLEM: Use of custom tray and tray adhesive is clinically recommended for elastomeric impression material. However there is not clear mention of drying time of tray adhesive in achieving appropriate bonding strength of tray material and impression material. PURPOSE: This study is to investigate an appropriate drying time of tray adhesives by evaluating tensile bonding strength between two types of polyvinylsiloxane impression materials and resin tray, according to various drying time intervals of tray adhesives, and with different manufacturing company combination of impression material and tray adhesive. MATERIAL AND METHODS: Adhesives used in this study were Silfix (Dentsply Caulk, Milford, Del, USA) and VPS Tray Adhesive (3M ESPE, Seefeld, Germany) and impression materials were Aquasil Ultra (monophase regular set, Dentsply Caulk, Milford, Del, USA) and Imprint II Garant (regular body, 3M ESPE, Seefeld, Germany). They were used combinations from the same manufacture and exchanged combinations of the two. The drying time was designed to air dry, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 25 minutes. Total 240 of test specimens were prepared by auto-polymerizing tray material (Instant Tray Mix, Lang, Wheeling, Il, USA) with 10 specimens in each group. The specimens were placed in the Universal Testing machine (Instron, model 3366, Instron Corp, University avenue, Nowood, MA, USA) to perform the tensile test (cross head speed 5 mm/min). The statistically efficient drying time was evaluated through ANOVA and Scheffe test. All the tests were performed at 95% confidence level. RESULTS: The results revealed that at least 10 minutes is needed for Silfix-Aquasil, and 15 minutes for VPS Tray Adhesive-Imprint II, to attain an appropriate tensile bonding strength. VPS Tray Adhesive-Imprint II had a superior tensile bonding strength when compared to Silfix-Aquasil over 15 minutes. Silfix-Aquasil had a superior bonding strength to VPS Tray Adhesive-Aquasil, and VPS Tray Adhesive-Imprint II had a superior tensile bonding strength to Silfix-Imprint II at all drying periods. CONCLUSION: Significant increase in tensile bonding strength with Silfix-Aquasil and VPS Tray adhesive-Imprint II combination until 10 and 15 minutes respectively. Tray adhesive-impression material combination from the same company presented higher tensile bonding strength at all drying time intervals than when using tray adhesive-impression material of different manufactures.

Impact of immediate and non-immediate provisionalization on the soft tissue esthetics of final restorations on immediately placed implants / 대한치과보철학회지

STATEMENT OF PROBLEM: Interpoximal papilla could be re-established without immeidate support with a provisional resotration following an immdiate implant placement. PURPOSE: Successful esthetic outcomes were reported utilizing immediate provisionalization following immediate implant placements. The aim of this study was to evaluate the soft tissue esthetics around immediately placed single tooth implant restorations with or without immediate provisional restorations. METHODS: A total of ten patients, who had a hopeless maxillary anterior tooth, were enrolled in this study. Screw retained provisional restorations were delivered to the randomly chosen 5 patients (immediate provisionalization group) on the day of immediate implant placement and maintained for about 5 months. For the remaining five patients (non-immediate provisionalization group), healing abutments were delivered on the day of surgery, replaced with screw retained provisional restorations approximately 3 months afterwards, and the provisional restorations were maintained for about 3 months. Digital photographs were taken at the delivery of final restorations in order to assess following variables; mesial papilla, distal papilla, soft tissue level, soft tissue contour and facial soft tissue prominence. The variables were compared to those of the contralateral natural tooth and scored by prosthodontists, periodontists, orthodontists and dental students. RESULTS: The immediate provisionalization group marked significantly higher scores on the following variables; soft tissue level and facial soft tissue prominence. In evaluating each variable, there were no notable differences in opinion between four dentist groups. CONCLUSION: Immediate provisionalization can be a treatment option to achieve superior soft tissue esthetics around immediately placed single implant restorations rather than non-immediate provisionalization approaches.

A study on the gratification of the patient in the dental hospital / 대한치과보철학회지

STATEMENT OF PROBLEM: Today's market economy has been changed more and more to consumer concerned. It is owing to not only consumers' rising standard of living and education, but also purchasers' easy accessibilities to products through various mass media. The consumer centered market system, where customer can choose items with diverse alternatives to satisfy their self esteem, is also applied to the field of medical business, and accelerated by an increasing income level of shoppers and introducing the whole nations'medical insurance system. Today, the medical industry has become competitive due to increasing number of medical institutions and medical personnel, and this offers wide choices to consumers in the medical market place. At this point of time, it is essential to survey on the primary factor of gratification for the patient in the Dental clinic, as well as on the problems and suggestions in medical service. PURPOSE: The analysis in this study shows essential factors and expected influential elements in satisfaction of the patient in the Dental Hopsital, and strategic suggestions for the provider of dental service, which can be of benefit to the prospective customer as well as can make improvement in the quality of dental treatment service. MATERIAL AND METHOD: This study had been researched by collecting and analyzing the organized questionnaires, which were filled in directly from 784 patients, who visit Dental Hospital, Yonsei University in Seoul, from January 23rd to April 15th. RESULT: It can be summarized like the followings. 1. The social and demographical peculiarities of respondents are as follows. Samples of gender and marital status are adequately extracted, but data on occupation and treatment are are under a bias toward students, undergraduates and graduate students, and orthodontics. 2. 74% of patients who answer the questionnaire were highly satisfied with the service of dental clinic in the section of overall satisfaction. 3. The survey result about specific service of dental treatment, within sections of independent variables, is like the followings; Patients are highly gratified with service system, kindness, explanation, explanation on expected waiting hours, reservation system, emergency measures, expert treatment, existence of knowledge of dentistry, size of hospital, disinfection, equipment and parking, but lowly satisfied with expense of treatment, preparatory hours for treatment, waiting hours, treatment hours and the period of subscription. 4. The correlation analysis showed that there is no significant linear relationship between the independent variables. 5. The probit regression analysis showed that 8 out of 34 independent variables explained the dependent variables at the level of 0.01. 6. It shows that 8 independent variables, which can affect customers'satisfaction, are clearing up of inconvenience, service system, kindness, explanation, treatment hours per attendance, reservation system, existence of knowledge of dentistry, and contentment of equipment in the hospital. CONCLUSION: The consumer's satisfaction totally relies on subjective evaluations of customers. Providing appropriate service, which can meet the criteria for the customer who demands various wares, pursues luxury goods, and expects high quality of medical service, is essential to fulfill patients'satisfaction. Many medical institutions do their best to satisfy their customer, touch their consumer, and offer patience centered services, and it is also applied to the field of dentistry. Establishing brand new strategic managements and elevating the quality of dental service based on this survey are required to improve the satisfaction of patience in the Dental Hospital.

Analysis of current nursing homes in Korea and to assess the role and prospect of dentists in comparison to Japanese long term care insurance system / 대한치과보철학회지

STATEMENT OF PROBLEM: The introduction of "The Long-term Care Insurance System"(a public nursing care insurance scheme) is scheduled from July in 2008. Lately, the importance of oral health care had increased. Introduction and establishment of the methodology (nursing care procedure) based on professional dental knowledge is inevitable. PURPOSE: The purpose of this study was to rouse recognition of the importance of dental care in the long term elderly care in nursing homes, with implementation of the new insurance law. MATERIAL AND METHODS: Visited two institutions for the elderly, Yudang Village and Sungjiwon located in Suwon city to investigate the present conditions in terms of (1) the detailsof the institution, (2) the activities concerning with dental care in the institution, and (3) the consciousness and recognition regarding dental care of the staffs. RESULTS: In two institutions, under the present conditions, oral cleaning (including the cleaning of denture) for residents was operated with no professional advices and limited professional dental care. It was found that there was very little awareness of aspiration pneumonia. The members of staff however, did recognizethe necessity of professional maintenance and management of oral care in daily nursing care, and that many residents hold dental problems. They were very eager in introducing the methodology (nursing care procedure) in dental care in nursing homes.

Oral health status and treatment need of institutionalized elderly patients / 대한치과보철학회지

STATEMENT OF PROBLEMS: In the area of dental care, the institutionalized elderly have placed the most vulnerable state, and we cannot find their subjective need of dental treatment because of the physical and mental disabilities, But we have no basic investigation of their oral health conditions. PURPOSE: The aims of the current study were to investigate the oral health status of institutionalized elderly patients who are in the least benefited side of dental service, and to analyze their dental treatment needs. MATERIAL AND METHODS: The survey of the oral status was carried out on 758 institutionalized elderly, and 212 elderly who was more than 65 years old from D dental office, and it was based on the Guidelines of Oral Health Research of year 2000 in Republic of Korea. RESULTS AND CONCLUSION: The DMFT index of the institutionalized elderly appeared higher than that of the same ages in control group, and it increased with age. The number of residual teeth of the institutionalized elderly appeared lower than that of the same ages in control group, and it decreased with age (p < .05). The number of fixed partial denture in institutionalized elderly was lower than that of the same ages in control group (p < .05). The percentage wearing removable partial denture was not significant between the elderly in institutions and the control group, and was not different according to age between the two groups. The percentage of institutionalized elderly wearing complete denture appeared lower than that of the same ages in control group, and it increased with age. The percentage of institutionalized elderly needing complete denture was higher than that of control group, and the percentage of elderly needing complete denture on the maxilla was higher than that of the mandible. 16.35% of the institutionalized elderly was living without denture in spite of their fully edentulous state. The need for complete denture increased rapidly with age. The number of valued teeth and dental prostheses in shortened dental arch concept and number of occluding pairs of teeth of institutionalized elderly were lower than that of the control group (p < .05). In institutionalized elderly, the number of residual teeth, the number of fixed partial dentures, and the percentage wearing removable partial dentures were higher in the mandible, and the percentage wearing complete dentures was higher in the maxilla (p < .05). The rate of institutionalized elderly needing prosthodontic treatment appeared to be 67.82%, where the number of occluding pairs of teeth was less than 10. When it is difficult to evaluate the subjective need of dental treatment as with the institutionalized elderly, estimation using the number of occluding pairs of teeth can be a useful indicator that can project treatment needs. For the oral health care of institutionalized elderly, it is essential to increase the awareness of nurses and caregivers who take care of them, about the importance of the oral health. Since the average life span and number of residual teeth are increasing gradually, the welfare policy should be changed to implementing regular dental examinations, preservative treatment forms and oral health control of dentulous patients where the traveling-treatment system and visit system are supplemented. And principles should be set that the present denture project of edentulous patients should be done by specialists who'll also be responsible for postmanagement. Through this research of institutionalized elderly, the oral health status which is worsened by aging could be confirmed. And the interest and positive participation of dental society on the elderly should come first in order to solve the rising treatment needs of the elderly patients.

Rehabilitation of a patient with a post radiotherapy trismus with an obturator and a maxillary denture using magnet attachments / 대한치과보철학회지

Construction of an obturator for rehabilitation of a patient who underwent a maxillectomy is vital. Routinely a constructed obturator includes denture portion. A patient who may present anatomical limitations due to surgical or radiotherapy complications often challenges the clinician. Purpose: This clinical report describes a patient with severe trismus after surgical resection and radiotherapy treatment of a tumor in the upper left maxilla. Conclusion: This report describes the concepts of using a rotational path insertion for an obturator and a separately constructed maxillary denture. The stability and retention of the obturator were obtained from anatomical features. Where as these were achieved through magnetic attachments and the remaining edentulous ridge to ensure esthetic and function of the prosthesis.

Marginal tissue response to different Implant neck design / 대한치과보철학회지

STATEMENT OF PROBLEM: Loss of the marginal bone to the first thread have been accepted but continuous effort have been made to reduce this bone loss by varying implant design and surface texture. PURPOSE: This animal study has examined the histomorphometric variations between implants with micro-thread, micro-grooved and turned surfaced neck designs. MATERIAL AND METHODS: Four mongrel dogs have been used the premolars removed and left to heal for three months. One of each implant systems with turned neck, micro-thread and micro-grooved were placed according to the manufacturers' protocol and left submerged for 8 and 12 weeks. These were then harvested for histological examination. RESULTS: The histologically all samples were successfully ossointegrated and active bone remodelling adjacent to implants. With the micro-grooved implants 0.40 mm and 0.26 mm of the marginal bone level changes were observed at 8 and 12 weeks respectively. The micro-threaded implants had changes of 0.79 mm and 0.56 mm at 8 and 12 weeks respectably. The turned neck designed implants had marginal bone level changes of 1.61 mm and 1.63 mm in 8 and 12 weeks specimens. A complex soft tissue arrangement could be observed against micro-threaded and micro-grooved implant surfaces. CONCLUSION: Within the limitations of this study, it could be concluded that implants with micro-grooved had the least and the turned neck designed implants had the most changes in the marginal bone level. The textured implant surfaces affect soft tissue responses.

Tensile bond strength between elastomeric impression materials and tray resins depending on the thickness of the tray adhesive / 대한치과보철학회지

STATEMENT OF PROBLEM: Elastomeric impression materials have been widely used to obtain an accurate impression. However there have not been enough studies on the influence of the thickness of the tray adhesives on the bonding strength between the trays and the elastomeric impression materials. PURPOSE: In order to understand the relationship between the thickness of the tray adhesive and the tensile bond strength and to suggest the thickness at which the bonding strength is strongest, tensile bond strength related to the thickness of adhesives of 3 different elastomeric impression materials were tested. MATERIALS AND METHODS: 3 impression materials, Permlastic(R) Regular Set(Kerr Corp., Romulus, Michigan, U.S.A.), Impregum(TM) Penta(TM)(3M ESPE, Seefeld, Germany), and Aquasil Ultra Monophase Regular Set Smart Wetting(R) (Dentsply Caulk, Milford, Delaware, U.S.A.), were used in this study, and tray adhesives from the same manufacturers of the impression materials were used, which were Rubber Base Adhesive, Polyether Adhesive, and Silfix, respectively. The tray specimens were prepared by autopolymerizing the tray material(Instant Tray Mix, Lang, Wheeling, Illinois, U.S.A.), and a PVC pipe was used to house the impression material. In group A, tray adhesives were applied in multiple thin layers of 1 to 5 and in group B, adhesives were applied only once, in the thickness equivalent to several applications. Lightness(L*) of the adhesion surface was measured with a spectrophotometer (CM-3500d, Konica Minolta, Sakai, Osaka, Japan). The tensile bond strength of the elastomeric impression material and the tray resin was measured with universal materials testing machines(Instron, Model 3366, Instron Corp, Nowood, Massachusetts, U.S.A.). A formula between the number of adhesive application layers and the lightness of the adhesion surface was deduced in group A, and the number of adhesive layers in group B was estimated by applying the lightness(L*) to the deduced formula. RESULTS: 1. In group A, a statistically significant increase in tensile bond strength appeared when the number of application layers increased from 1 to 2 and from 4 to 5, and no significant difference was present between 2, 3, and 4 layers in Permlastic. In Impregum, the tensile bond strength was significantly increased when the number of adhesive layers increased from 1 to 3, but no significant difference after 3 layers. In Aquasil, the tensile bond strength significantly increased as the number of application layers increased up to 4 but showed no significant difference between 4 and 5. 2. In group B, the tensile bond strength was decreased when the thickness of the adhesive increased in Permlastic. Impregum showed an increased tensile bond strength when the thickness of the adhesive was increased. In Aquasil, the tensile bond strength increased as the number of adhesive application layers increased up to approximately 2.5 layers but it sharply decreased after approximately 4.5. CONCLUSION: From the study, the common idea that it is better to apply a thin and single coat of tray adhesive needs correction in more detailed ways, and instructions on some of the tray adhesives should be reconsidered since there were several cases in which the tensile bond strength increased according to the increase in the thickness of the adhesives.

Factors influencing patient satisfaction with complete dentures / 대한치과보철학회지

STATEMENT OF PROBLEM: In spite of the progress in techniques and materials in complete denture prosthodontics, patients still complain of discomfort after the insertion of complete dentures. For the last several decades many prosthodontists tried to find factors influencing patient complete denture satisfaction, however the reported results became a controversy. PURPOSE: The purpose of the present study was to verify the factors influencing patient satisfaction with complete dentures using multiple regression analysis. MATERIALS AND METHODS: 33 patients who visited the department of prosthodontics, dental hospital of Yonsei University, 4 to 6 weeks after the complete denture delivery, were asked to complete the questionnaires on complete denture satisfaction, social variables and psychological variables. The Prosthodontists who treated the patients with complete dentures were also asked to complete the questionnaires on evaluation of patients' oral condition and technical quality of dentures. The factors influencing patients' satisfaction with their complete dentures were analyzed using multiple regression analysis. RESULTS: Among the patients' sociodemographic variables, the variables of relationship with children, economic status, housing condition, other people's opinions of dentures and gender were the influential factors on patients' satisfaction with complete dentures. Patients showing the symptoms of depression, one of the psychological variables, were dissatisfied with their complete dentures. In spite of the good oral condition, patients were dissatisfied with complete dentures, whereas the technical quality of dentures did not influence patients' complete denture satisfaction. CONCLUSION: According to the results above, patients' sociodemographic and psychological variables rather than clinical variables including oral condition and technical quality of dentures were the influential factors on complete denture satisfaction. The results of this study may not only enable prosthodontists to predict the success and failure of complete denture treatment, but also help both prosthodontists and patients be informed of the essentials of increasing satisfaction with complete dentures.

A study on the visco-elastic properties of four currently used tissue conditioners / 대한치과보철학회지

The dimensional stability of tissue conditioners characterizes the ability of the materials to yield accurate functional impressions of oral mucosa. This study evaluated the viscoelastic property and the linear dimensional changes with the factor of time and thickness of tissue conditioners (COE-COMFORT(TM), Visco-gel, COE-SOFT(TM), Soft-Liner) The thickness of these materials were changed (1.5mm, 3.0mm) and the percentage changes in dimension were measured at 1h, 12h, 24h, 36h, 3day, 7day after specimen preparation. From the results large differences appear between the various tissue conditioners. The results suggest that the period recommended for forming functional impression would be 2-3days after insertion in the mouth. in addition, it is important to select tissue conditioners suitable for functional impression because of the wide range of dimensional stability among the materials.

COMPARISON OF THE ACCURACY OF STONE CASTS MADE FROM ALGINATE IMPRESSION MATERIAL BY MIXING METHODS AND APPLICATION OF TRAY ADHESIVE / 대한치과보철학회지

The use of alginate impression materials today is prevalent because of its efficiency and simplicity in clinical settings. Unfortunately, the simplicity of the procedure tends to lull the dentist into a sense of well-being, and lead him into using careless or sloppy technique. Alginate impression materials are used to fabricate diagnostic and preliminary casts, and the final cast. Incorrect use of this material is known to affect the accuracy of the final prosthesis. The purpose of this study was to compare the effect of different mixing methods of alginate impression material and tray adhesive on the accuracy of the stone cast produced by each method. A total of 30 stone casts were produced by using 3 different types of mixing methods (10 stone cast for each mixing method, respectively) The first method utilized an automatic-mixing machine to mix alginate while the second method was carried out manually, strictly following manufacturer's instructions. The third method also involved manual mixing, but did not follow the manufacturer's instructions and was done in a random fashion. Also, 20 additional stone casts were produced by using alginate with or without tray adhesives were included in the study to evaluate effects of tray adhesives on the accuracy of alginate impression. 10 stone casts were produced by adding tray adhesives to the interior surface of the impression tray prior to taking the impression. The other 10 excluded this step. A total of 50 stone casts were analyzed by the three-dimensional measuring machine to measure and compare the dimensional changes of the impression material of each group. The results are as follows. 1. No significant difference was found between the automatic mixing group and the manually-mixing group(p>0.05). 2. For the group that followed manufacturer's instructions, less dimensional changes were recorded than the group that didn't in measuring distance d4(p<0.05) 3. The group that used tray adhesives showed less dimensional changes(p<0.05). The findings revealed that mechanical methods of mixing alginate impression materials had little influence on dimensional changes. However, it is proven that following manufacturers instructions in alginate impression taking is an important step in acquiring accurate impressions and tray adhesives may play an important role in enhancing the results.

Comparative Histomorphometric Analysis Of Mandible And Iliac Bone On Bone Density / 대한치과보철학회지

To demonstrate possible influences of general bone density on the mandible, histomorphometric analysis was carried out in mandibles and iliac bones and the correlation of the two bone densities was tested. Comparison of bony density in women and men over 60 years in the mandible was carried out too. Quantitative computed tomography (GCT) was taken in cross-section of mandibles at the same site where histomorphometric analysis was performed to evaluate the reliability of QCT. The analysis included 40 cadavers with no known disease affecting the bones. The subjects consisted of 15 females and 25 males with a mean age of 60.3 years. Spearman correlation analysis and Wilcoxon rank sum test was performed. The results were as follows. 1. There was statistically no correlation between the mandible and iliac bone in the walues of corrected cortical width (CCW), cortical porosity (POR) in cortex, and total bone volume(TBV), mean trabecular plate thickness (MTPT), mean trabecular plate density (MTPD), and mean trabecular plate separation (MTPS) in trabecular bone. 2. Comparison of women and men over 60 years, men had statistically higher bone density than women except for POR of buccal and lingual cortex, and MTPD of alveolar trabeculae in mandible. 3. There was statistically significant correlation between TBV of trabecular bone and CT NO., but not between POR and CT No. In mandible. According to the results above, there was no correlation between mandible and iliac bone density and between mandibular bony density and age. Further studies are required to support the results. A more noninvasive method to be able to measure the bone density of mandible should be developed and it is necessary to accumulate data on the normal values of bone density of mandible according to age and sex. Further study should be carried out about QCT to measure mandibular bony density using QCT.